Accessories : Wire
|
- IR-EW01, IR-EW02, IR-EW08 / TTL
- IR-EW03, IR-EW04, IR-EW09, IR-EW10 / RS-485
- Basic Connector Wire (IR-EW05~07)
- Power Gender Jack (IR-AG01)
- TTL/PWM Molex Connector 10 Housings & 30 Terminals (Bulk) (IR-MC02)
- RS-485 Molex Connector 10 Housings & 40 Terminals (Bulk) (IR-MC03)
- Connector Rubber Cap (IR-MC04)
Extension Wire
IR-EW01
We offer extension wires as below for application in your facilities.
IR-EW01 : 1,000mm length with/ 3pins TTL
Molex connectors (50-37-5033)

Extension Wire
IR-EW02
IR-EW02 : 2,000mm length with/ 3pins TTL
Molex connectors (50-37-5033)

Extension Wire
IR-EW08
IR-EW08 : 500mm length with/ 3pins TTL
Molex connectors (50-37-5033)

Extension Wire
IR-EW03
We offer extension wires as below for application in your facilities.
IR-EW03 : 2,000mm length with / 4pins RS-485
Molex connectors (51065-0400)

Extension Wire
IR-EW04
IR-EW04 : 4,000mm length with / 4pins RS-485
Molex connectors (51065-0400)

Extension Wire
IR-EW09
IR-EW09 : 500mm length with / 4pins RS-485
Molex connectors (51065-0400)

Extension Wire
IR-EW10
IR-EW10 : 1,000mm length with / 4pins RS-485
Molex connectors (51065-0400)

Basic Connector Wire
IR-EW05,
IR-EW06,
IR-EW07
We offer Basic Connector Wire as below for application in your facilities.
IR-EW05 : 200mm length with / 3pins TTL Type
Molex connectors (50-37-5033)
(Already included in the actuator package)
5pcs



IR-EW06 : 200mm length with / 3pins PWM Type
Molex connectors (50-37-5033)
(Not included)
5pcs



IR-EW07 : 200mm length with / 4pins RS-485 Type
Molex connectors (51065-0400)
(Already included in the actuator package)
5pcs



Power Gender Jack
IR-AG01
The IR-AG01 is a power gender jack between AC/DC adapter power jack and power terminal on our various control boards (see below).
Please check if the jack of the adapter you have meets the size specification below.
This product is supposed to be assembled by the customer referring to the assembly manual.
Components before assembly
Assembled product
[ Specification ]
Outer diameter 5.5mm / Inner diameter 2.1mm
Maximum allowable current : 7.5A
Input voltage : 12V
EC381V terminal block applied




[ Components ]
① Terminal Gender : 1pcs
② Terminal Block : 1pcs
③ Wire(Red +) : 1pcs
④ Wire(Black -) : 1pcs




* (Caution) If the directions of ①Terminal gender and ②Terminal block is connected incorrectly (reversely), it will cause fatal damage to the circuit parts which will be connected with gender jack, so please make sure correct polarity.
* (Caution) Always pay attention to safety when assembling using tools.
[ How to Assemble ]
After checking the + and – marks of the ① Terminal gender,use a phillips screwdriver to loosen two screws(A) in a counterclockwise
direction. Make sure that they do not come out of the hole.
Referring to B, put the ③(red+) and ④(black-) wires into ①Terminal gender, then completely tighten two screws(A) clockwise.
After checking the + and – marks of the ① Terminal gender,use a phillips screwdriver to loosen two screws(A) in a counterclockwise
direction. Make sure that they do not come out of the hole.
Referring to B, put the ③(red+) and ④(black-) wires into ①Terminal gender, then completely tighten two screws(A) clockwise.
As described in the left drawing, rotate the two parts ① and ② by 180O(upside down). Prepare to fasten two wires (③Red+, ④Black-) to ②as shown in the right drawing.
Put the wires ③(red+), ④(black-) into ② Terminal block, then use a flat-head screwdriver to completely tighten two screws(C) clockwise. After assembly, check out that ①, ② directions and ③, ④ wire color are correctly assembled as shown in the drawing below before use.
[Control boards that can be used with IR-AG01]
IR-USB02 PC USB Interface
IR-CT01 EZ Controller
IR-STS01 Arduino Servo Tester Shield
IR-STS02 Raspberry Pi HAT




TTL/PWM Molex Connector 10 Housings & 30 Terminals
IR-MC02
TTL/PWM Molex Connector 10 Housings & 30 Terminals(Bulk)
– Molex connector/housing set for our actuators.
– For the customers who need to make their own wire harness with the experience in assembling cables.
– Cable Crimper is required.
– Pay close attention not to make mis-wiring or contact failure.
– Molex connector/housing set for our actuators.
– For the customers who need to make their own wire harness with the experience in assembling cables.
– Cable Crimper is required.
– Pay close attention not to make mis-wiring or contact failure.
3Pin Housings : 10EA
3Pin Terminals : 30EA
Molex 3P TTL Male Housing 05037-5033 : 10pcs
Molex 3P TTL Male Terminal 00870-1039 : 30pcs
Molex 3P TTL Male Terminal 00870-1039 : 30pcs
* Shipment from Korea
* If you wish to get product from USA, please click here.
RS-485 Molex Connector 10 Housings & 40 Terminals
IR-MC03
RS-485 Molex Connector 10 Housings & 40 Terminals(Bulk)
– Molex connector/housing set for our actuators.
– For the customers who need to make their own wire harness with the experience in assembling cables.
– Cable Crimper is required.
– Pay close attention not to make mis-wiring or contact failure.
– Molex connector/housing set for our actuators.
– For the customers who need to make their own wire harness with the experience in assembling cables.
– Cable Crimper is required.
– Pay close attention not to make mis-wiring or contact failure.
4Pin Housings : 10EA
4Pin Terminals : 40EA
Molex 4P RS-485 Male Housing 51065-0400 : 10pcs
Molex 4P RS-485 Male Terminal 50212-8000 : 40pcs
Molex 4P RS-485 Male Terminal 50212-8000 : 40pcs
Connector Rubber Cap
IR-MC04
Connector Rubber Caps, 10pcs in a set.